Doc inlet temp during regen
After cleaning the doc it was reinstalled on the truck, reset doc/dpf counters. Performed manual stationary regen, the truck kicks up to 1200-1300 to start regen, the turbo speed starts at around 42k and turbo actuator 92%, egr valve position consistently stays at 0%, exhaust gas pressure about 140, intake manifold pressure about 12.5.DPF inlet temperature: 550°C; Soot load: 4.1 g/dm3. It should be noted that there was almost no NO2 generation over the DOC during active regeneration. This ...
Did you know?
During regen the temp doesn't get over 305. I thought it had to hit over 500 to kick on injector 7. ... We removed the DPF and DOC and got them baked and blew out. ... Constant regens. Two obd codes. Inlet trap pressure and particulate trap 1 ...To create the thermal conditions necessary for soot regeneration in the CSF, fuel was injected into the exhaust pipe up-stream of the DOC (Fig.2). In this study the conditions for fuel injection were fixed to 25ml/min, 300°C inlet temperature and 49,000/hr space velocity for the DOC to generate a CSF inlet temperature of 600C.Verification Parked Regen 1. Connect DDDL 7.09 SP2 or newer. 2. Turn the ignition ON (key ON, engine OFF). 3. ... (DOC) inlet temperature sensor, the DOC outlet temperature sensor and the Diesel Particulate Filter (DPF) outlet temperature sensor. ... During parked regeneration the exhaust gases will be extremely HOT and could cause a fire ifGood morning Roy, I replace the SCR Outlet Temp Sensor yesterday ran a regen and it went on forever, had to sop it after one hour. The Temps slowly build up, these are the readings after about 1 hour DOC inlet-747 DOC Oultet 1010 DPF Outlet 1092 SCR inlet 1028 SCR Outlet 1045 What do yuo recommend next Still showing same codes SCR NOX ...Jun 19, 2016 · Fengjun Yan. Control of diesel oxidation catalyst (DOC) outlet temperature is critical for downstream diesel particulate filter regeneration, but is challenging to control due to the non-minimum ... CM871 High DOC temp during regen. Hi everyone, I have regen issue with my 2009 Volvo with CM871. During Regen instead of DOC temp staying steady and DFP temps going up, this engine shows DPF outlet temp staying steady while DPF intake and DOC temps keep going up (1000+). I have this truck for 3 years and every forced regen i …ASL: DOC Inlet Temperature ASL: DOC Outlet Temperature ASL: ASL: SCR Outlet Temperature ASL: SCR Inlet NOX Sensor After-treatment Outlet NOX ASL: Nox conversion AAS: Fuel Doser In'ection Status ASL: Exgas mass rate 'd Connections (paused} Device LMCM21J MCM21T MCM21T CPC04T MCM21T MCM21T MCM21T ACM21T …SUBJECT: Modified Parked Regeneration Concerns ISSUE The call center has received a number of calls regarding concerns about the modified parked ... modified parked regeneration utilizes increased DOC inlet temperature to clean the DOC inlet face. Excessive torque loads can cause parked regenerations to abort. In some cases the . 19 TS-6 - 4 -Diesel Oxidation Catalyst Temperature Drift - Inlet High or Outlet Low Table 1. SPN 3242/FMI 20 Description 70°C (126°F) Difference During Non-regeneration Mode Monitored Parameter Diesel Oxidation Catalyst (DOC) Inlet Temperature vs. DOC Outlet Temperature Typical Enabling Conditions Coolant Temperature Greater than 60°C (140°F); Regen not ...[Server Time: 10/03/2022 09:26:18 pm] This Forum is English-Only!!!,... Donations help keep the lights on around here, Thanks in advance...AlanJ Discussion starter · Mar 10, 2020. While trying to get my head around OBD Fusion and what all the PID data represents, I was able to capture a regen in process. What I had expected to find was when the 'soot %' reached 100%, the regen would start and that's exactly what happened. What I didn't expect was what happened to the EGT reading.Vehicle fails to regen. During High idle regen, DOC outlet max 479 F , Command boost pressure 0%, fuel doser inject ... DOC inlet temp doesn't go past 495 degrees. DOC stops around 515 and DPF temp is at 495. Checked for exhaust leaks = none f ...Diesel Oxidation Catalyst: The DOC assists in elevating temperatures into the DPF to initiate the regeneration process. Fuel is injected into the exhaust by the Hydrocarbon (HC) fuel dosing system. The injected fuel is oxidized in the DOC, which raises the temperatures above passive mode operating temperatures.Regen Temperature- Out Of Range Low Table 1. SPN 3556 /FMI 1 Description This code sets when the exhaust temperature does not increase above the modeled threshold when a regeneration is enabled. Monitored Parameter DOC outlet temperature sensor Typical Enabling Conditions Regeneration enabled, 1100 to 2050 rpm, 50% to 100% engine load. This guide will assist with diagnosing regen related codes and issues for GHG14 DD Engines. Engine Speed 1100 rpm (1275 rpm during first 12 minutes of regen …My unit starts the regen but the DOC inlet temp is only getting to 420 degrees and is not allowing to burn off for the regen. I’m getting codes 4752, (intake manifold pressure sensor) 3719, 3711. Will the intake manifold pressure sensor not allowe the regen to get the DOC inlet up to the proper 520 degrees in order to fully perform the regen ... During parked regeneration the exhaust gases will be extremely HOT and could cause a fire if directed at combustible materials. The vehicle must be parked outside. 11. Perform High Idle Regeneration. 12. When regeneration is complete, clear all fault codes. 13. Road test the vehicle. a. If no fault codes appear, testing is complete. Verify ...The catalyst should also exhibit low light-off temperature, to enable active regeneration during periods of operation with lower engine load. Figure 4 illustrates the light-off performance with post injection of fuel and exhaust injection of fuel for a fresh and aged DOC. The x-axis represents the inlet temperature of the DOC. During parked regeneration the exhaust gases will be extremely HOT and could cause a fire if directed at combustible materials. The vehicle must be parked outside. ... Refer to section "Removal of the Intake Pressure/Temperature Sensor". Verify repairs. 11. Visually inspect exhaust system for leaks or damage, including manifold, gaskets ...Aug 23, 2011 · During a proper regen, DOC inlet temp, or temp #1, should be about 550-600. DOC outlet temp, or temp #2, should be 1000-1200 degrees. DPF outlet temp should be 950 to 1200. In a healthy system, the engine injects fuel into the exhaust during a regen that the DOC burns to create the heat. The heat is used to BAKE down the collected soot in the DPF.
1 NUMBER: 2 ATS 07 S.M. REF.: Listed in Table 1 ENGINE: ATS DATE: April 2007 SUBJECT: UPDATES TO AFTERTREATMENT SYSTEM TROUBLESHOOTING PUBLICATION: 7SE63 The Aftertreatment System Technician's Guide has been revised. MANUAL REFERENCE Section 6.1, Mechanical Troubleshooting 9.1, SPN 3242/FMI , …Decided the doc inlet temp sensor should be replaced and the DOC/DPF be sent out for cleaning. They didn't look to bad after I took them out the the cleaning test said they needed to be cleaned. Reassembled everything and did another parked regen. DPF outlet temp stayed about 50F above inlet temp during the entire regen.CM871 High DOC temp during regen. Hi everyone, I have regen issue with my 2009 Volvo with CM871. During Regen instead of DOC temp staying steady and DFP temps going up, this engine shows DPF outlet temp staying steady while DPF intake and DOC temps keep going up (1000+). I have this truck for 3 years and every forced regen i did was successful ...Monitor temperature rise across DOC during regen. Little<br /> or no temperature rise indicates DOC not active.<br /> Monitor DOC inlet temperature. No temperature change<br /> after engine startup indicates sensor problem.<br /> Listen for the ITV to sweep at key up.<br /> Turbo not functioning properly Perform a turbo …
Now this truck is back and will not regen. The truck is in a fail safe mode for soot. Initially it was setting a SPN 3351 FMI 7 for the engine exhaust back pressure valve and the DOC/DPF were not getting hot. I adjusted the valve and the DOC inlet hit 500 and outlet hit over 600, DPF outlet was able to get over 500. The truck is not dosing fuel ...ASL: DOC Inlet Temperature ASL: DOC Outlet Temperature ASL: ASL: SCR Outlet Temperature ASL: SCR Inlet NOX Sensor After-treatment Outlet NOX ASL: Nox conversion AAS: Fuel Doser In'ection Status ASL: Exgas mass rate 'd Connections (paused} Device LMCM21J MCM21T MCM21T CPC04T MCM21T MCM21T MCM21T ACM21T ACM21T ACM21T ACM21T ACM21T MCM21T ACM21T You are correct the inlet should be higher then the outlet, in the above post I just stated in backwards. During the regen mine were reversed, (inlet low, ... My DPF inlet temp will reach 1250, outlet temp ... JMBT. 08-03-2016, My DOC inlet never goes over about 650oF and usually stays in the low 6's. Quick serve says 550-750 is ...…
Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Regen Temperature- Out Of Range Low Tabl. Possible cause: Ran an onboard filter cleanliness test to get the regen temps. Soot lo.
COOLANT TEMPERATURE: 209F DOC INLET: 432F DPF INLET: 421F DPF OUTLET: 411F Last edited: Jun 10, 2017. 4vmach1, Jun 10, 2017. 4vmach1, Jun 10, 2017 #71 + Quote Reply. Trucking Jobs in 30 seconds. ... During one of the parked regen the delta-p set a out of range on the data monitoring, but hasn't done it since then. ...Exhaust Gas Temperature 1 – DOC Inlet (Degrees Fahrenheit). Description. Gauge; TXD ... Time since Active Regen (Hours) · DEF Level (%) · DEF Temperature (°F) ...Diesel Oxidation Catalyst: The DOC assists in elevating temperatures into the DPF to initiate the regeneration process. Fuel is injected into the exhaust by the Hydrocarbon (HC) fuel dosing system. The injected fuel is oxidized in the DOC, which raises the temperatures above passive mode operating temperatures.
Jan 18, 2020 · Mack MP8 regen issues. 2012 CXU613 with 2012 fault codes so it's not a 2013. Truck arrived at the shop at the beginning of the week. Soot load was level 5. performed a parked regen. DOC inlet temp was bias. DPF outlet temp stayed above inlet temp during regen. Oct 26, 2018 · Engine Speed 1100 rpm (1275 rpm during first 12 minutes of regen then 1100 rpm for fuelmap ending in ZGS 999) Turbo Speed 45,000 – 60,000 (turbo is used to create pressure in the DD13 and DD15AT only) Fuel Cut Off Valve 100% (once DOC inlet temp reaches 536° F) Engine Torque Around 5% Actual Torque Load 15 – 18% (greater than 20% may ...
Diesel Oxidation Catalyst Temperature Drift - Inlet Symptoms of a clogged DPF filter are excessive regens and long regens, last ing 60 minutes or longer. You can monitor temperatures/pressures when doing a forced regen to make sure everything is in range and working properly. Faulty … Temperature should begreater than 100 C (212 F) prior to parkedVolvo D13 regeneration. we have couple of trucks on our fl Tue 11/28. 90° /76°. 65%. Times of clouds and sun with a couple of showers. RealFeel® 98°. RealFeel Shade™ 95°. Max UV Index 5 Moderate. Wind ENE 2 mph.SUBJECT: Modified Parked Regeneration Concerns ISSUE The call center has received a number of calls regarding concerns about the modified parked ... modified parked regeneration utilizes increased DOC inlet temperature to clean the DOC inlet face. Excessive torque loads can cause parked regenerations to abort. In some cases the . 19 TS-6 - 4 - Accumulated soot can be burned with the target temperature for c-DPF 7. Start the engine and run a Parked Regen. Monitor DOC inlet pressure and engine speed during the regen. Compare your DOC inlet pressure reading to the screen shots below to identify a possible cause of the fault code. a. If the DOC inlet pressure starts out high above 10 kPa (1.45 psi) and decreases during the parked regen, this No; replace the drifted SCR temperature sensSoot load was level 5. performed a parked regenThe addition of engine exhaust to intake a NOTE: The sensor box (item 8) contains the SCR inlet and outlet NOx sensors, DPF outlet pressure sensor, and the DOC inlet pressure sensor. 1. DOC Outlet Temperature Sensor. 2. DOC Inlet Pressure Sensor Port. 3. DOC Inlet Temperature Sensor. 4. Front Heat Shield. 5. DEF Nozzle. 6. Exhaust Outlet. 7. DEF Metering Unit. 8. Sensor Box (see note ...Non-uniform fuel supply across the catalyst inlet face may also cause non-uniform and incomplete fuel oxidation over the DOC and lead to non-uniform DOC outlet temperature and durability challenges. In cases where … Vehicle fails to regen. During High idle regen, DOC o Malfunctioning temperature sensors. The temperature sensors, spread through the aftertreatment system, measure the exhaust going into and out of each filter. The first sensor is in the DOC and the last is after the SCR. The sensor’s readings measure how well the system is working, and a faulty sensor can interfere with the regen process.Exhaust Gas Temperature 1 – DOC Inlet (Degrees Fahrenheit). Description. Gauge; TXD ... Time since Active Regen (Hours) · DEF Level (%) · DEF Temperature (°F) ... CM871 High DOC temp during regen [Server Time: 10/15/2023 05:21:3[During parked regeneration the exhaust gases will be extremely HOTIf the system doesn't reach this then something is wrong with The calibration results of (a) DPF outlet temperature and (b) DPF pressure drop during active regeneration. DPF regeneration conditions: DPF SV = 20,000 h-1 , DPF soot loading = 4 g/L, DPF inlet ...Jan 18, 2020 · Mack MP8 regen issues. 2012 CXU613 with 2012 fault codes so it's not a 2013. Truck arrived at the shop at the beginning of the week. Soot load was level 5. performed a parked regen. DOC inlet temp was bias. DPF outlet temp stayed above inlet temp during regen.