Did you know?

Litter-Robot 3: Reset Button. The Reset button will reset your Litter-Robot's Cat Sensor. You can think of the Cat Sensor as the scale and the Reset button as a way to zero the scale. IMPORTANT: Any time you do anything that affects the weight or placement of the unit, including adding or removing litter, emptying the Waste Drawer, or moving or ...Litter-Robot Cats Litter Box III 3 Open Air DFI Hardware. by Litter-Robot. Write a review. How customer reviews and ratings work See All Buying Options. 0 total ratings, 0 with reviews ...Hi, litter robot 3 connect blue flashing light (fast flashing). Have taken the robot apart a few times, cleaned the sensors. ... 2- Wipe the DFI sensor’s circuit boards on each side. 3- Install the new bag. 4- Press the “Reset” button on the robot. 5- Reset the level on the app.How to replace your Litter-Robot's Cat Sensor. Posted on 15/01/2018 by pjutras in Domestic, Pet Care, Litter-Robot, Consumer Robotics. Tags: cat sensor , Litter-Robot , Litter-Robot Open Air , repair , Tutorial. 8318 3 7. Like Share.Hello, I have basically the same problem with my litter robot 3 connect. I have tried everything within the trouble shooting like the person said above, I’ve only had it for 1 week. As well I’ve tried to level out the floor for the sensor. But the main problem I am having is the connect only connected to the app successfully for 3 days. And then any …Hello @Mariagav , Thank you for your reply. According to your order number, the robot is no longer under warranty. If the cleaning of the DFI sensor didn’t fix the issue, we recommend replacing it so you can order a new one from this link: We also recommend replacing the 3 sets of pins so you can order new ones from these links: The following …Unplug the wire from each pinch bar and remove the bars from the plastic slots. Now take some pliers, tin snips, or whatever you have laying around and cut a clean, non-corroded piece of the pinch bar off so you have a small piece of metal. If you're going to bypass both the bonnet and the pinch bars, you'll want to cut off two small pieces of ...Hardware concerned: Litter Robot III Connect. Software concerned: N/A. Troubleshooting steps already taken: unplugging it and plugging it in again. cleaning the unit. slightly opening the pin in the power jack. making sure that it is plugged directly into the wall using its original power adaptor.The DFI sensor that you have received is the new version and it looks different but it has the exact plastic brackets so you can easily install them the same way as the older sensor: Let us know if you need further assistance. ... Litter-Robot 3 Open Air DFI Hardware (v2) ...The laser version only exists on a limited production run in 2020, and when those fail, they replace them with the original IR sensors. Despite my LR3 being out of warranty, they sent me a replacement IR and pinch sensor kit free of charge (this is the first and only time I've needed service).Litter robot 3 stops mid cycle. I have had the litter robot air for 2 months and it was working fine but recently it has started to stop every few seconds during cycle. The yellow light flashes and cycle continues after 15 secs but then stops again and again even after the robot is returning to its home position.Purchase replacement pinch contact and drawer full indicator (DFI) circuit board assembly for your Litter-Robot 3. ... (DFI) circuit boards for your Litter-Robot 3. Contact Whisker Support if your robot is still under warranty The store will not work correctly in the case when cookies are disabled.In this case, the DFI sensor and the 3 sets of pins will need to be replaced so we will send you new ones under the warranty. The following videos will show you how …Came home to my Litter-Robot in the upside down position and the yellow flashing (2 flashes per second) and I cannot get the globe to turn at all to try to reset itself. There is power to the unit because the yellow light is flashing but regardless of which buttons I press or turn power on/off no movement of the unit can be made. I have cleaned and …Cleaning the sensors. With the globe, bonnet, and drawer removed, lean the unit backward so that you can look into the holes on the bezel to see each sensor. Using a clean, dry cotton swab, carefully clean the surface of each sensor to remove any dust. It is important to note that it will be very difficult to see any dust, specifically on the ...The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If a cycle is interrupted or the bonnet is removed, the unit will stop, and the yellow light will flash slowly, about 1x per second. This will also occur if the cat sensor is activated by a cat entering the globe.I have successfully bypassed the DFI sensor permanently with a under kitchen led tape light section. It has been running for over 1 month 100%. Very easy to do and cost effective that you can do yourself. ... Switched from the Litter Robot bags and am getting 3 more days between emptying.The issue that you are having would require replacing the DFI sensor and the 3 sets of pins so you can order the following parts from the following links: RobotShop Europe Litter-Robot 3 Open Air DFI Hardware (v2) Litter-Robot 3 Open Air DFI Hardware (v2) Replacement DFI Hardware for your Litter-Robot 3 Compatible with Litter-Robot 3 …You can try to clean the 2 green circuit boards and the 2 plastic brackets of the DFI sensor using isopropyl alcohol and a Q-Tip to remove any rust or dust from them. If that didn’t help, the DFI sensor will have to be replaced first in order to make the robot functional again. Let us know if there’s anything else we could assist you with.Purchased to repair my Litter robot 3 the service received was excellent and the part arrived on the Monday after ordering on the Friday. Geniene Gordon . 01/02/2024 . ... We had to install the new DFI sensors the day we were leaving for a week away, so the time pressure was massive. Mary was extremely helpful by replying to my emails ...

Upgrade your Litter-Robot 3 to Connect to get all the perks of the app with this do-it-yourself installation kit! With a WiFi-enabled Litter-Robot, you can use our app to: View the waste drawer level. Change settings remotely. Receive status notifications. Monitor your cat's litter box usage. Control multiple Whisker robots.May 23, 2021 · How to install a replacement DFI Sensor Kit and Pinch Detector Terminals in the Litter-Robot III Open Air. Oct 19, 2022 · How to install a replacement DFI Kit + Pinch Detect Terminals in the Litter-Robot 3. The DFI Circuit Board and brackets may appear different from what is pictured depending on when the unit was ... Litter-Robot 3 is equipped with infrared emitters and sensors located above the waste drawer that check if the drawer is full each time the globe returns to the Home position. Once a full waste drawer is detected, the unit will indicate it is full with a blue flashing light.

The pinch sensors are a constant source of annoyance: they corrode and stray litter also makes them malfunction. The DFI sensors (drawer-full optical sensors) are unreliable and need to be replaced for $80 from time to time. My latest set of DFI sensors is a little different so it looks like they've redesigned these, so hopefully these won't ...Our litter robot 3 has been barely working for a while. I'd have to hit reset and cycle for it to actually work. Well, about 2 weeks ago it over rotated during a cycle and became "stuck" (wouldn't rotate back into starting position). Putting it back manually caused a yellow flashing light that wouldn't go away.…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. The issue that you are having would require replacing the DFI senso. Possible cause: Hi! I’ve installed a new DFI sensor and circuit-board for the Litter Ro.