Did you know?

Product: LaserJet M1217 nfw MFP. Operating System: Microsoft Windows 10 (64-bit) My LaserJet M1217 nfw MFP printer is stuck in the initializing phase upon startup. It appears that it cannot go past this phase of startup and it is stuck in a loop. I tried a hard reset (unplug power cord from wall and back of printer, remove USB cable, wait 2-3 ...2.With the printer turned on, disconnect the power cord from the rear of the printer. 3.Unplug the power cord from the wall outlet. 4.Wait at least 60 seconds. 5.Plug the power cord back into the wall outlet. NOTE: HP recommends connecting the printer power cord directly to the wall outlet.Sep 1, 2021 · This is what I have tried: -unplugging the printer for various amounts of time, for up to 5 minutes before plugging in again. -held down the power button while plugging it in. -using HP print and scan doctor, it fails to communicate with the product, with and without USB cable.

Yes No. davidzuts. 7,130 918 558. Level 13. 11-13-2014 05:16 PM. I have seen the 94% issue and it can be many things. Best thing to do is remove all paper, remove printheads and ink cartridges. Now start the printer and see if it comes to where is asks for the ink item first and then for the paper.We will have to perform an NVRAM reset on the printer that may help. The reset instructions are specific for your printer and performing those steps on a different printer may corrupt the device. I've sent you a private message with reset instructions, follow the reset instruction to perform a full reset and re-initialize the printer.Reconnect the power cord to the rear of the printer. Turn on the printer, if it does not automatically turn on. The printer might go through a warm-up period. The printer lights might flash, and the carriage might move. Wait until the warm-up period finishes and your printer is idle and silent before you proceed. Keep me posted. 🙂Welcome to HP Support Community. This is a great place to post questions and find answers. Thank you for posting your query, I will be glad to help you. I see that your HP LaserJet Pro M1212nf Multifunction Printer is stuck on an initializing loop. I suggest that you follow the steps listed below to reset the printer. 1.

Hp color laserjet enterprise m652 Stuck on initializing. 1 -Power cycled - removed power from back, removed ethernet cable, let sit for 10 seconds, pressed the power button in for 10 seconds the plugged directly into wall . 2- Cold reset - held down the X on startup and performed the cold reset under startup optionsHP M477 fdw, stuck on Initializing i have replaced. Scanner, formatter board Permanent initialized and no luck any help will be highly appreciated - 9004638 ….

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Hp printer stuck on initializing. Possible cause: Not clear hp printer stuck on initializing.

Yes No. davidzuts. 7,130 918 558. Level 13. 11-13-2014 05:16 PM. I have seen the 94% issue and it can be many things. Best thing to do is remove all paper, remove printheads and ink cartridges. Now start the printer and see if it comes to where is asks for the ink item first and then for the paper.There are the two orange rings to pull to remove the foam insert and the setup instructions. Setting Up the Printer Hardware for HP Color LaserJet Pro M177fw MFP Printers. Try again to manually move the carousel if the issue persists. Open the scanner lid and the lid below that so you should see the toners.If you think you have received a fake HP Support message, please report it to us by clicking on "Flag Post". I move this printer from Windows Server to Windows 7 (32 bit processor) frequently. As far as trying to correct the issue, I have disconnected - 5949124 - 2.

01-18-2017 10:32 AM. In my case I unplugged the machine and disconnected the 3 scanner connectors and then powered on. It didn't start up, but after removing power and plugging the scanner connectors back in and powering the machine up I was able to get it to the ready state. I updated the firmware and cycled power without an issue.Please perform the hard reset and check. Turn the printer on, if it is not already on. Wait until the printer is idle and silent before you continue. With the printer turned on, disconnect the power cord from the rear of the printer. Unplug the power cord from the wall outlet. Wait at least 60 seconds.I read your HP LaserJet Pro MFP M225dn Printer is stuck on initialization. I would like to help you resolve this issue. Perform a Hard Reset on the printer. Remove the power cable from the printer when it is turned on. Press and hold the power button for 60secs. Connect the power cable to printer and directly to wall outlet. Turn on the printer.

volleyball motto I see that you are facing an issue with your printer stuck on Initializing screen. A) Please follow the steps below to perform a power drain. 1) Take out the cartridges. 2) Unplug the power cord from the printer & wall. 3) Press and hold the power button down for 15 seconds and release the power button, wait for about 30 seconds. research chemical supplykorean day spa san francisco If the issue persists, we will have to perform a factory reset. The reset instructions are specific for your printer and performing those steps on a different printer may corrupt the device. I've sent you a private message with reset instructions, follow the reset instruction to perform a full reset and re-initialize the printer.Oct 4, 2022 · Welcome to HP Support Community. This is a great place to post questions and find answers. Thank you for posting your query, I will be glad to help you. I see that your HP LaserJet Pro M1212nf Multifunction Printer is stuck on an initializing loop. I suggest that you follow the steps listed below to reset the printer. 1. rasheem ryelle carter If you encounter your HP Printer stuck on initializing, perform a hard reset, bypass the initializing phase, and power drain the printer motherboard. If the issue persists, cold reset the printer to restore factory default settings and update the firmware. carmax commercial actorrasheem ryelle carterfidelity relationship manager salary Press and hold down CANCEL and > (right arrow button) at the same time while powering on printer. c. Continue to hold down buttons until the control panel display reads PERMANENT STORAGE INIT. d.Release the buttons. Printer will return to Ready automatically. 5. Close and Lock the Carriage latch close the top cover and switch ON the printer. 6. Printer should initialize and display a message to insert printheads as shown in the image below: 7. Select Options under printhead menu and select replace printhead. 8. Open the Top cover and Disengage the Carriage latch. 9. ryan poston shayna 10-26-2021 03:30 PM. Our Laser Jet Printer M1217nfw has worked great for many, many years...however today we found the machine is constantly tying to initialize. The printer is hardwired to the internet and hardwired to two computers on our network. We can print from both of our computers but the printer will not scan for us or send faxes ... bryant's seafood world menukevin jelichthe lakes at grand prairie Welcome to the HP support community. I understand that your printer screen is stuck, I am glad to assist you. You might have to perform an NVRAM reset on the printer to fix this issue. The reset instructions are specific for your printer and performing those steps on a different printer may brick the device.The reset instructions are specific to your printer and performing those steps on a different printer may brick the device. I've sent you a private message with reset instructions, follow the reset instructions to perform a full reset and re-initialize the printer. In order to access your private messages, click the private message icon on the ...