Did you know?

Kurupt_Introvert. •. Flashing yellow to red means the motor has detected an obstruction or jam. Turn the unit off and remove the bonnet and globe. Check for gear or motor obstruction. Reassemble the unit and verify a proper litter level. Then turn the unit on—if the problem persists, try the Litter-Robot 3 Troubleshooter or contact Whisker ...Cat sensor troubleshooting. In this article we will troubleshoot the "Bonnet removed" message. If you received a "Cat sensor interrupt" notification in the Whisker app, refer to the Litter-Robot 3: Yellow flashing slowly (Cat sensor) guide. If …I think the new litter robot has a weight feature built in to it now but it didn’t when I was purchasing and that feature alone has been so helpful in noticing trends in our cats’ weights. I also liked with the Pura X that the globe is completely enclosed and the top can serve as a lounge area for the cats still. ... Blue blinking light ...

If your robot has problems with the yellow blinking light, please follow the troubleshooting below to determine whether the issue is due to excess weight, the …Troubleshooting. If your Litter-Robot 3 is displaying a yellow light flashing quickly, this indicates a cycle has been interrupted by the Anti-Pinch safety feature and you will need to inspect the pinch sensor. Inspect the sensors. The purpose of the pinch sensor is to detect if an object is blocking the waste port during the globe rotation.Blinking Blue Light, Blinking Yellow Light, and Blinking Red Lights. Mostly, the reasons for blinking blue light will be discussed. But sometimes this blue light blink gets combined with the yellow LED or red LED. So, it is necessary that you have the required knowledge of all the LEDs and what they mean. The Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times per second. You will also receive a notification on ...

Reply. litterrobot. •. That Blue flash followed by the rapid Yellow flash is indicative of a failure in the Drawer Full Indicators and Pinch Detect Terminals. If your Litter-Robot is in Warranty, give our Customer Experience Specialists a call at 877.250.7729.Replace the bonnet by inserting the bonnet tabs into the rear bonnet slots, then press the latches while rotating it forward until the latches click into place. From the Home position, press the Reset button to zero the weight sensors. The Litter-Robot should return home displaying a blue 'ready light' status. ….

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Litter robot troubleshooting blinking yellow light. Possible cause: Not clear litter robot troubleshooting blinking yellow light.

1K. 158K views 4 years ago. Here's what I told Litter Robot, " Every time it’s used, it half cycles and I have to power it off and power it back on for it to cycle. Pushing …Status Indicator Lights. Solid Blue: Feeder is in Automatic Feeding Mode. Solid Yellow: Hopper is low indicating less than 20% food remaining. Solid Red: Hopper is critically low indicating less than 5% food remaining. Flashing Red: Dispenser is jammed. Solid Purple: Food Bowl and Food Chute are full for 12+ hours (food has not been consumed)

Litter-Robot 4 features a bonnet that covers the globe and functions as a guard for the waste port as the globe rotates. Sensors on the unit detect if the bonnet is on or off. This ensures that Litter-Robot will not rotate if the bonnet has been removed. If your unit displays a yellow light bar flashing, this indicates that the bonnet has been ...The unit will cycle again 15 seconds after your cat has left the globe or 5 seconds after the bonnet is replaced. If your Litter-Robot is not detecting your cat or not cycling, complete the troubleshooting steps in our Litter-Robot 3: Cat not detected guide. If your Litter-Robot is slowly flashing yellow or stuck upside down due to the cat ...

gill house henderson harbor ny Test the cat sensor. Test the cat sensor by pressing the top of the entryway (not the bonnet) down and away, toward the back of the unit. You should be able to feel a slight spring/bounce movement - this is a good sign that the robot can freely move and that there are no obstructions to prevent the cat sensor from functioning. Reply. litterrobot. •. That Blue flash followed by the rapid Yellow flash is indicative of a failure in the Drawer Full Indicators and Pinch Detect Terminals. If your Litter-Robot is in Warranty, give our Customer Experience Specialists a call at 877.250.7729. sherman oaks movie theatermarkie martin husband If your Litter-Robot 3 is displaying a yellow light flashing slowly, this indicates a cycle has been interrupted either by the cat sensor or bonnet removal. Press the Reset button to resume the cycle. If your unit returned home and displays a solid blue light, you've been successful. If your unit is not displaying a solid blue light after ...Submit support request. Select a category for your ticket. Select a sub-category for your ticket. Please describe your issue. Got questions or issues? Contact Litter-Robot Support today. We’re dedicated to ensuring a seamless experience for you & your pet. family dollar harmony nc If your unit has a blue light bar with partial yellow flashing or the unit will not cycle, this indicates that the scale has been triggered for more than 30 minutes. You will also receive a notification on your phone if you use the Whisker App. Place the unit on a firm, level surface. Avoid soft, uneven, or unstable flooring for accurate weight ...Need assistance with your Litter-Robot 4? Find guides & troubleshooting tips. Get the support you need today. The store will not work correctly in the case when cookies are disabled. ... Litter-Robot 4: Blue light bar with yellow blinking WiFi (Onboarding mode) Litter-Robot 4: Blue with partial yellow flashing (Excess weight detected) Litter ... calsaws verificationjolting in up down mannerlittle caesars w el camino Watch on. If your unit displays a yellow light bar, this indicates that the unit has been "paused". Pressing the Cycle or Reset button should get it to resume cycling. If it does not, please power the unit off and back on using the Power button. If your unit displays a blue light bar, you've been successful. If your unit is still displaying a ...The Litter-Robot 3 is equipped with Cat Sensor that detects when a cat enters and exits the globe. To ensure the accuracy and reliability of the Cat Sensor,... college confidential kenyon If your robot has problems with the yellow blinking light, please follow the troubleshooting below to determine whether the issue is due to excess weight, the … mc clubs in wisconsingvec emailpedicure middletown de 1K. 158K views 4 years ago. Here's what I told Litter Robot, " Every time it’s used, it half cycles and I have to power it off and power it back on for it to cycle. Pushing …